Видео

Thank you!

Hello! It will be a bit expensive also about the shipment, and dont know if i can find again all the pieces to convert one more!

@@de-lab if I have one of those.. I can send it to you ..

@@smithbayca1 it will need around 350-400 to convert it, not included the cost of the shipment, radio and battery pack

io ho usato quello elencato nella lista, ma va bene un qualsiasi altro servo a basso profilo che abbia le stesse dimensioni, di almeno 10-13kg di coppia, puoi usare qualsiasi altro cingolo ma serve una ruota dentata adatta poi

@@de-lab va bene

no, non fanno contrassegno, paghi in anticipo e poi spediscono, fai attenzione che se scegli il magazzino in cina, applicheranno anche le spese doganali!

@@de-lab ok grazie

ciao, grazie! Uso una futaba T10J

Si può usare anche un altro radiocomando?

@@veranieddu8833 si certamente, l'importante che abbia un numero di canali sufficiente e che possa fare i mix fra due canali per utilizzare i cingoli

Quanti canali deve avere il radiocomando per far funzionare i componenti elencati per questo bruder?

@@veranieddu8833 servono almeno 6 canali!

many thanks!!!

they are plugged in 2 different channel and then i made a mix on my radio with those channels

@@de-lab ok thanks. Just for example so that I understand/do it correctly, I'm new to (RC ), one servo on channel 3 and the other on channel 5, mix 1=channel 3 is master and channel 5 slave?

@@caymanite_rc_construction yes correct! and then set the gain 100% for both!

ahahah thank you!!

thank you! the tracks are the original of the bruder model, not the best but them works fine, an upgrade would be change the traction wheen and put the huina 1580 tracks, but by now it works fine

Thank youu

i've used the original attach of the bruder and then 2 push rods connected on the servo!

watch the video from 14:20 min

@@de-lab got that but they are close together they look smeller then the other ones that you used I think anyway maybe I’m wrong

@@dennisfreitas7675 yes maybe are a little bit smaller, then you can try to cut them and make it shorter

@@de-lab that crossed my mind sorry for all questions but I do love your video’s you do great work

Try to find one with the same size and torque, 10 or more kg is enough, but not less than 10, then you have to get the same size 😉

@@de-lab besides cutting the pin on the servo is there anything else that has to be done because I cut the one I have and it still does not go around

@@dennisfreitas7675 you have to check of its cutted good, try to turn with hand before you assemble the servo again, or just take care to the Potentiometer of the servo

thank you! if need help just write me!

@@de-lab thanks

it's an huina 580 v1 but totally changed and upgraded!

@@de-lab 😲woow you have worked hard, you can hardly recognize a Huina in it👏👏

@@lukaszpbear6 yes is totally change now!

Thank you!!

Ahahah thanks!!!

Not for sale at the moment 😁

@@de-lab alrighty I might try to make one

Hello! what you mean for engine control module? i have not used ESC for the track, just only servos

Hi sir. How can drive same forward and can turn. How its wiring sir

You need to mix the channel from your radiocontrol

Thank you very much bro.

@@RECKLESSMOTORstudio welcome!!

i think it's much better to install servos, 1 because you will not need to have esc inside and it's a way to save space, 2 its stronger than have 2 micro n20 motors, 3 you have to get the great speed for that and with servos you will not need to going crazy and search for the right rpm on the engines, thats why i prefer to use servos!

si, un servo ad ogni canale, altrimenti non hai modo di comandarli singolarmente, potresti solamente andare avanti o indietro, vanno collegati in 2 canali diversi e poi tramite i mix sulla radio, uso la trazione su un unico stick

hello Romi, dont need to install some esc because it' working just with servos, when you install the servos for the traction you have to open the servo and remove the stopper on the gear, then it will rotate at 360° but will work as a normal servo, just take care to set the inner dimmer of the servo, at the 0 point or death point so it will not move alone while your stick is on the 0 position

there is anything printed in 3D!

@@de-lab yes, I know, but I did not found it on the website if you can share the link to download it.

I not used 3D parts 😀

Nice!!

grazie!!

Like 29

grazie!!